Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
Nearly everybody may have their own thoughts with regards to A Step-by-Step Guide to Installing a Bathtub.
Mounting a bathtub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately difficult project. If the old tub is readily available, the project can move quickly; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the job is much harder. In either situation, the job is within a house handyman's skills, although you will certainly require a helper to leave the old tub and set in the new one. Make sure you have certified on your own for the work and also fit attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is better to think about employing one before you begin. Chances are you may need a professional plumber to make tube links.
This post will certainly assist you set up a new tub in your restroom if you have already bought a brand-new bathtub and also do not need to change the setup of your previous water system pipes.
Your tools and also product checklist should consist of the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, activate the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making sure that the washers remain in area between the tap as well as the sink. Safeguard the faucet in position with the producer supplied backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the tap ends initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Making use of both wood boards under its feet, put the tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and changing the feet on the tub up until the spirit level reads level.
To mount faucets, fit all-time low of the furthest versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply and also examine all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last setting.
Preparing for the Setup
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to ensure that if the tap includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to prevent pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its last position.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, resulting in issues with wetness and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when looking around the search engines. Those who liked our article plz do not forget to share it. Thank-you for taking the time to read it.
Quote & Schedule
Report this page